Why are my LED string lights not working?

Whether you're using traditional incandescent lights or LED lights, most plug in Christmas lights usually stop working for the following reasons: The circuit isn't carrying power . A fuse has blown. A bulb has burnt out and has created a cascading outage.

What is USB powered fairy lights?

The USB-powered LED fairy string lights are evenly spaced on copper wire that can be bent to accommodate any shape . These LED Fairy Lights emit warm white or yellow illumination that is controlled by the included handheld remote (CR2025 battery included).

Why are my LED lights not working when plugged in?

One common reason LED lights may not turn on is due to a faulty power source . Please check if your LED lights are plugged in and that the power source is functioning normally. Additionally, check the power cord for damages or loose connections. Another reason LED lights may not turn on is due to a faulty LED bulb.

Do USB LED lights use a lot of electricity?

Installed as your light source, LED strip lights guzzle less electricity to produce the same light output. The potential savings are very significant – LEDs draw up to 85% less electricity than conventional incandescent lighting , and around 18% less electricity than CFLs (Compact Fluorescent Lamps).

Are USB lights any good?

Power Output: While USB rechargeable wall lights provide sufficient illumination for small areas or as accent lighting, they may not be as powerful as wired lights . If you require brighter lighting for larger spaces, you may need to consider alternative lighting options.

What causes string lights to stop working?

Wiring: It's possible that the wiring in the string has been damaged , which could cause it to fail. Check the wiring for any breaks or damage, and replace any damaged sections. Storage: If the lights were not stored properly, they may have been damaged or exposed to moisture, which could cause them to fail.

Why are my LED strip lights not turning on?

Check the power supply to ensure it is not damaged and is providing the correct voltage. If your LED strip lights won't turn on, you might need to replace the LED Driver. Check out What is an LED Driver? LED strip lights offer a convenient and cost-effective lighting solution.

Do LED string lights burn out?

The simple answer is no. Over time LED lights will eventually fade away, but they don't burn out .

enbrighten 70512 USB-Powered LED String Lights Instruction Manual (2024)

Table of Contents

enbrighten 70512 USB-Powered LED String Lights
INSTALLATION
OPERATION
TROUBLESHOOTING
FCC
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

enbrighten 70512 USB-Powered LED String Lights

Thank you for your purchase!

Instructions made easy

Read instructions or watch easy-to-follow video. Scan code orvisitbyjasco.com/70512i

Register your product

Receive exclusive deals and register your product. Scan code or visitbyjasco.com/deals

INSTALLATION

STEP 1: INSTALL STRING LIGHT
Carefully untie the string light and hang, wrap or place it in your preferredindoor or covered outdoor location. Ensure the 13ft. USB power cord is withinreach of a power source.

STEP 2: UNTIE POWER CORD
Carefully untie and straighten out the USB power cord.

STEP 3: PLUG INTO USB-A PORT
Plug the USB power cord into a 5V, 1A minimum USB-A port or adapter (notincluded).

STEP 4: PREPARE REMOTE
Remove the plastic tab from the remote’s battery compartment (CR2025 batteryis preinstalled).

OPERATION

ON/OFF BUTTONS: ON/OFF
DIM BUTTONS: Increase/decrease brightness (4x)
COLOR BUTTONS: Choose from 16 solid colors

HOLIDAY BUTTON:

July 4th
Holiday
Mardi Gras
Valentine’s Day
Autumn
Spring
St. Patrick’s Day

MODE BUTTON:

Pulse
Flash
Strobe
Fade

NIGHT MODE BUTTON:

Solid amber
Pulse amber

SPEED BUTTONS : Increase/decrease speed (4x)
3H/6H BUTTONS: Light turns off after three or six hours — lights will flash once to confirm timer is active.
DAILY BUTTON: Light stays on for eight hours, turns off for 16 hours — lights will flash once to confirm timer is active.
TIMER OFF BUTTON: Deactivates 3H, 6H or Daily — lights will flash twice to confirm timer cancellation.

NOTE : Point the remote directly at the USB controller to avoid extra IRinterference.

TROUBLESHOOTING

Problem	Possible Cause	Solution

Light doesn’t work

| Won’t turn on|
Incorrect USB power| USB power supply must be 5V @ 1A minimum for properoperation. Excessive voltage may lead to product damage.
Remote doesn’t work| Remote battery| Replace CR2025 battery noting polarity.Reference diagram on back of remote.
Contact our U.S.-based Consumer Care at

1-800-654-8483 between 7AM-8PM, M-F, Central Time

WARNING

RISK OF ELECTRIC SHOCK
RECEPTACLE OUTLETS USED FOR POWERING CURTAIN LIGHTS SHALL COMPLY WITH ALL NATIONAL AND LOCAL ELECTRICAL CODES. CONSULT LOCAL ELECTRICIAN IF UNSURE OF COMPLIANCE REQUIREMENTS.
DO NOT SUBMERSE.
DO NOT USE AROUND AQUARIUMS.
DO NOT USE IN WET LOCATIONS.
DO NOT INSTALL IN LOCATIONS WHERE CURTAIN LIGHTS CAN BE STEPPED ON.
ENSURE CURTAIN LIGHTS ARE UNPLUGGED FROM POWER DURING INSTALLATION.
CURTAIN LIGHTS SHOULD BE INSTALLED OUT OF CHILDREN’S REACH. DO NOT ALLOW CHILDREN TO PLAY WITH THEM.
RISK OF FIRE
NOT INTENDED FOR USE NEAR OPEN FLAMES OR ABOVE STOVES, COOK TOPS, SINKS OR OTHER HEAT PRODUCING APPLIANCES, SUCH AS COFFEE MAKERS, TOASTERS OR TOASTER OVENS.
USE INDOORS OR IN PROTECTED OUTDOOR LOCATIONS ONLY.

Suppliers Declaration of Conformity | Model # 70512 |
Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114,www.byjasco.com.
This device complies with Part 15 of the FCC and Industry Canada licenseexempt RSS standards. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may causeundesired operation.

FCC

FCC NOTE: The manufacturer is not responsible for any radio or TVinterference caused by unauthorized modifications to this equipment. Suchmodifications could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy, and if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee interference will not occur ina particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3(B)/NMB-3(B)

MADE IN CAMBODIA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited warranty. Visitwww.byjasco.comfor warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7AM-8PM, M-F, Central Time.

enbrighten 70512 USB-Powered LED String Lights Instruction Manual (2024)

enbrighten 70512 USB-Powered LED String Lights

INSTALLATION

OPERATION

TROUBLESHOOTING

FCC

References

Read User Manual Online (PDF format)

Download This Manual (PDF format)

FAQs

Why are my LED string lights not working? ›

References